Ventum-s turntablesrotating ring design

The system:

The Ventum-S rotating ring turntables develop the modular system principle even further in a logical way.

The example of the 8.0 m turntable illustrates the modular system very well: a turntable with a diame-ter of 8.0 m can also be used for 4.0 m and 6.0 m sizes. Turning rings, which expand the 4.0 m inner ring, can be used separately and combined with each other.

Are you looking for onE system for:

stage installations, stages, stands and technical stage sets, constructing trade fair stands, walk-in, multi-storey designs, camera and lighting towers, ramps, stairways and stairway equipment, ceilings, three-dimensional lighting elements, illuminate fabric walls ... ?

The modular system components and component families can be combined with each other in a vari-ety of ways and therefore create a variety of solutions; the basic equipment consists of many parts.

A portfolio of possible solutions for your projects – available at any time …

… with one system that creates results with the speed that you need, guarantees safety during cons-truction because of the structure of the system and enables you to plan and look after your finances i the long term. you can reliably introduce your ideas with an unlimited number of options.

For component compatibility plus modular system variability.

Each component can be used in the component family and is therefore useful when developing solutions.

The component families for the Praktikabel, bridge and stairway modules all function according to this system. these component families complement each other and are completely compatible within the modular system so that you can find an effective solution.

A construction can be lifted, moved and lowered again. After the travel process, the construction stands safely and firmly on the ground.
The moving/lifting elements are completely retracted into the construction and no longer have any contact with the ground. Additional locking devices are not required. Our lifting device is therefore also suitable for sloping stages, for example.

Our lifting device is predestined for movable constructions where the payload is significantly higher than the dead weight.
A typical example of this are, for example, grandstands that stand safely and firmly on the ground when loaded (with an audience) and can be moved quickly and safely when unloaded (without an audience).

By lowering the construction, no visible driving gap remains, which is certainly advantageous from an aesthetic point of view.

Alternatively, the construction can be set down on fixed castors in order to move it easily and safely in a chosen direction. Later, you can freely move your construction in the jacked-up state for assembly and disassembly.

We have an electrically operated system (battery-based), which has relevant advantages especially compared to the widely used pneumatic systems. The advantages of our electric lifting system are listed below.

• Synchronous lifting process – the lifting process takes place in absolute synchronism, even if the individual rollers are loaded with different weights.
• Lifting force is 600 kg per roller – this results in a lifting load of 2400 kg with 4 rollers. If a higher lifting capacity is required, it can be extended as required in the master-slave system.
• Lifting height 30 mm – to compensate for unevenness in stage floors and deflection of the construction.
• Flat design – 141 mm when retracted – so the wheel fits into the classic step of 167 mm.
• 100 mm diameter rolls – to safely drive over crevices and edges in the stage floor.
• Easy, quick assembly – fits perfectly into our Ventum-S system frame and is fixed by only two screws with wing nuts. The battery and control unit are also mounted and dismounted easily and quickly using two quick-release clamps.
• Removal possible in a lowered state – if, for example, a grandstand is to be left at one location for several days, the lifting equipment can be removed in a lowered state and used in another construction.
• Charging of the batteries with a standard 24V charger – one battery charge is sufficient for 4 castors for considerably more than 30 lifting operations under full load.
• Neutrik cable plug connections between the control unit and the drives.

The Mecanum basic module is manufactured with the following dimensions: 1.0 x 1.0 x 0.2 m (total height: 0.224 with a floor panel).

This consists of a Ventum-S system bridge measuring 1.0 x 1.0 m, 2 axles (each with 2 Mecanum wheels), a control unit (SPS, radio receiver, booster, battery block) and a wireless remote control unit.

The combination of Ventum-S system bridges and insert carriages enables us to create scenery wagons with various dimensions.

Depending on what is needed in terms of dimensions and load, as many as 8 synchronised basic modules can be used.

The universal bevel adapter, which can be inclined by +/-20° and height-adjusted by 270 mm, allows surfaces of any inclination to be set up.

The support distance can be variably adapted to the frame length and the required load capacity.

Universal incline adapters can also be used as a continuous height adjustment option without inclination.